For:
VITA vPad excellence beginning with serial number 2820172050
VITA vPad comfort beginning with serial number 3020180051

VITA Zahnfabrik provides serial number-dependent software updates for model ranges of the devices mentioned above.

For this reason, you should check your serial number directly on the system before performing a software update.

Please only perform the software update if the serial number of your vPad is within the indicated range.

These software updates relate to the systems specified above and have been provided in generation-specific versions due to extensive hardware and software changes. At IDS 2015, several software features were introduced that were based on the models of the previous generation, and could not be implemented on the models mentioned above due to specific hardware incompatibility.

If you are interested in upgrading to the new software and hardware features, you can do so at any time by purchasing the latest generation of equipment, such as the control unit. The new control units are easy to install with dental furnaces from the series mentioned above of the generation prior to IDS 2015. 

Content of software update 200107 for VITA vPad excellence from serial number 2820172050
– Transfer of the user password when importing a password-protected profile 
– Transfer of the pellet number when importing a self-created press program 
– When canceling "Quickstart," the newly calculated start values were still adopted
– File names may contain special symbols
– Images and PDFs can be transferred from mobile devices to the vPad via the FURNACE App
– Japanese language added
– Warning of excessive wear of the heating elements, due to a temperature gradient in the sintering curve that is too steep. 
– New material VITA AMBRIA added
– New material VITA LUMEX added.


Content of software update 200107 for VITA vPad comfort from serial number 3020180051
– Transfer of the user password when importing a password-protected profile 
– Transfer of the pellet number when importing a self-created press program 
– Japanese language added
– Warning of excessive wear of the heating elements, due to a temperature gradient in the sintering curve that is too steep. 
– Materials can be copied from the VITA profile to the laboratory profile
– New material VITA AMBRIA added– New material VITA LUMEX added.


Content of software update 200107 for vPad SMART.FIRE 
– Optimization of the progress bar in the file manager
– Addition of the progress bar in the file manager 
– Resetting of the pre-drying temperature when the pre-drying phase is terminated 
– Clarification of the validator dialog messages 
– File names may contain special symbols
– Images and PDFs can be transferred from the mobile device to the vPad via the FURNACE App
– Japanese language added
– Clock time is synchronized with online time, and the change between daylight savings/standard time takes place automatically
– The creation of a full backup of the vPad on a USB flash drive is possible
– A simple web browser has been installed
– Process data can be sent online to VITA at the press of a button
– Support via the FURNACE App has been added
– Updates can be conducted directly online in the future. The vPad informs the customer whenever a new update is available. The update can then be downloaded and installed at the press of a button.
– A guided initial device setup has been added
– An additional silver firing (965°C) has been added to the furnace settings
– In the firing curve view, altered but not saved values are visually highlighted
– New material VITA LUMEX added.


Content of software update 200107 for VITA VACUMAT 6000 M/MP and VITA ZYRCOMAT 6000 MS
– The heating is switched off if the mains voltage drops below the defined value 
– Pellet number recognition has been optimized
– Multipump: Removal of error message "Vacuum has not been achieved" after the firing has been stopped 


Content of software update 200107 for VITA ZYRCOMAT 6100 MS
– To increase the lifespan of the heating elements, the heater is warmed up more gently in standby mode
– Heating controller has been optimized


Content of software update 191203 for VITA V60 i-Line
– The heating is switched off if the mains voltage drops below the defined value 
– New material VITA LUMEX added.

In order to keep the updates clear, there is an applicable furnace update for every vPad update associated with the same software version number.

VITA recommends performing software updates in order to ensure smooth operation of your systems.

Should you have any questions or comments regarding the software updates, please call VITA Equipment servicing: 
Telephone number: +49 (7761) 562 222
email: instruments-service@vita-zahnfabrik.com.