Parece que de momento Ud. se encuentra en Estados Unidos.
Take 3D printing to the next quality level with VITA VIONIC BASE RESIN IMPACT, an impactresistant printing material for removable denture bases. The excellent impact resistance of the product reduces the risk of breaking under stress.
In addition to the fracture work, the high flexural strength and optimized modulus of elasticity values ensure a balanced property profile, forming the basis for long-lasting dentures.
Long lasting
Patients benefit from long-lasting dentures, thanks to the impact resistance of the material, which reduces the risk of breaking under stress. Low plaque adhesion contributes to wearing comfort.
Well balanced
The well-balanced mechanical property profile is impressive in terms of fracture work, flexural strength and modulus of elasticity.
Excellent processing
Short printing times, low shrinkage and high fitting accuracy are just as compelling as the great polishing characteristics.
For the fabrication of denture bases.
Impresoras validadas:
Unidades de poscurado validadas:
Unidades de lavado validadas:
Para consultar declaraciones de conformidad se requiere el acceso a MyVITA. Mediante el siguiente enlace se podrá registrar en MyVITA.
Registrarse ahoraCan soft liner be applied to a printed denture made of VITA VIONIC BASE RESIN IMPACT?
Yes, the following soft relining materials have been tested:
Can printed dentures be relined or repaired?
Yes, printed denture bases made of VITA VIONIC BASE RESIN IMPACT can be relined/repaired.
1) Roughen the surface
2) Apply cold-curing polymer (e.g., Schütz Dental Futura Gen pink opaque or Merz Dental “Weropress pink”)
What does impact resistance mean?
Fracture work values indicate how well a component/material can absorb shocks and impacts (impact energy).
By taking measurements, you can find out at what load the material breaks or starts to give.
The impact strength measurements can be used to draw conclusions about the durability of denture bases, for example.
An impact-resistant denture base material reduces the risk of breakage but does not eliminate it (impact-resistant ≠ unbreakable).
The breaking strength in the event of a fall is highly dependent on the angle of impact and the impact surface. An unfortunate angle and a hard surface will increase the chances of the dentures breaking. This applies to all material types.
What devices have been validated for use with VITA VIONIC BASE RESIN IMPACT?
VITA VIONIC BASE RESIN IMPACT is compatible with a wide range of commonly used printers and post-curing units. A current list of successfully validated devices can be found on the product page under the "System compatibility" tab.
What bonding gap settings are recommended for combination with printed or milled teeth?
|
Material combinations |
Recommended bonding gap |
|
Printed denture base and printed denture teeth made from VITA VIONIC DENT RESIN |
150 µm |
|
Printed denture base and milled teeth made from VITA VIONIC DENT DISC multiColor: |
150 µm |
|
Printed denture base and pre-milled denture teeth VITA VIONIC VIGO: |
100 µm |
How many objects can I print if my bottle weighs 850 g / 600 g / 350 g?
|
Gross weight of the bottle |
Number of printed objects |
|
1100g |
approx. 50-70 pc. |
|
850g |
approx. 39-50 pc. |
|
600g |
approx. 27-30 pc. |
|
350g |
approx. 15 pc. |
How many denture bases can I print from 1 kg of denture base resin?
Approx. 50 denture bases can be printed from 1 kg of VITA VIONIC TRY-IN RESIN.
The actual number of printed objects that can be produced using 1kg of resin depends on several factors, such as the number of support structures, whether the resin is stored in the print tray or whether material is lost when it drips off.